CE approved Auto Paint Bake Oven Cheap Paint Booth For SaleBooth Body:EPS or Rock wool panel
Wall panel :sandwich style,thickness 50mm,polystyrene or cock wool available as required .
Panels are tongue and groove connected .Roof panel is galvanized metal sheets,hot-isolated panel as optional .
Door:new style is without aluminum side,reinforcement inside,while old style is with aluminum side.
Personnel door with pressure lock automatically opens when inside pressure exceeds.
There is auto-return device on top of personnel door of some models .
Basement is made of steel ,galvanized ,easy assembled .
2rows of grids and 3rows of vein boards, or full grids,good bearing ,antisepsis and reliable .
Ramp :2pcs or full vein boards.
Intake and exhaust Cabin
Centrifugal fan,big vane and motor separated ,avoiding accidents resulting from short circuit .Centrifugal fan produces great air flow ,is easy to clean dust on vane,and is up to CE standard. In take fan is a must for all models ,while exhaust fan is collocated for some models.
European flange style ducts.Exhaust ducts are must for all models while intake ducts are collocated for some models.Manual or electrical damper to adjust air flow .
Spraying-baking transform damper ,air controlled .
Intake and exhaust ducts are separated ,avoiding interaction
Twice filtration:the first one is at inlet,filtering dust above 15um,the second one is at the bottom of roof air chamber .multi-layers, good seal ,filtering dust above 5um ,up to 98% filtration rate. Four sides of filters are hided in the support trough ,assuring good seal .
Heating : Diesel burner ,fired after flame,reliable and completely burnt.
Heating exchanger ,made of stainless steel, large exchange area ,and high efficiency.
Lighting :Top lights:45° assembled,tubes are different according to different models.
Sides lights:differ according to different models,700-1000Lux lighting.
Control board : Control box :high quality components ,overload ,overheat ,phase-lacking protection.Heat sensor at
inlet works when heat exceeds .The whole operation can be done after spraying/baking is preset once.
SCM as optional as required .
Anti-fire: anti-fire device installed between cabin and generator as optional as required .
Anti-fire door closes when too much smoke or flame occurs,avoiding flame into cabin
Water paint device :Water paint device as optional .Two rows or three rows of nozzles installed on each side of top 45°,
Or 2 extra nozzles device at the rear corners Traditional booths can be changed into water paint boos
in this way.
Enviromental protection system : 4 types environmental-protection systems as optional .
Water curtain as optional as required.
|Model||BD720 (European Ceiling Type)|
|external size (mm)||7010x5570x3610|
|internal size (mm)||6900x4000x2800|
|Floor grids||Two rows grids ,grids area:10m2|
|Basement (H)||Galvanized steel plate ,300mm|
|Drive in ramps||2pcs 2000x620mm|
|Wall panel||Sandwich style ,50mm thickness polyester panel (EPS)|
|Roof panel||Galvanized steel plate|
|Entrance door||3pcs ,3200x2700mm ,metal plate without aluminum side ,reinforcement inside|
|Service door||1piece ,800x2000mm ,with pressure lock ,with safety glass window|
|ceiling lighting||8units,each4x36w ,LED tube|
|Filter cloth||Pre-filter ,G3 grade fiber glass filter|
|Ceiling filter ,F5 grade high efficient filter|
|Floor &exhaust filter ,G2 grade fiber glass filter|
|Heating system||Heating exchanger ,Stainless Steel 1Gr18Ni9Ti (SUS304) 160KW|
|Burner model||Diesel fuel burner Riello G10,100000Kcal/H|
|Inlet fan||7.5kw big impeller turbo fan ,25000m3/h|
|Control system||Painting ,warm painting ,baking ,baking time set, lighting ,emergency stop|
|Power supply||380v/50hz/3ph , special voltage is available|
|Optional||Side lights :8units ,each 2*36w ,LED tube|
|Rock wool panel ,50mm|
|Big ramp:2000*1000mm ,2pcs|
|Double intake centrifugal fan|
Packing Standard :
Each part all has label number which is easy for installation .
Model of transportation is mainly with container transportation .
The product is modular needs one set 1.5T forklift to be loading & unloading tool .
It only needs 2 operations to finish the unloading .